fbpx

CUBO 300 NC – FLAT

CUBO 300-NC FLAT CNC automatic bandsaw

CNC automatic bandsaw,hydraulically driven. Mitre cutting from 0° to 45° left in automatic cycle and from 0° to 60° left in semiautomatic cycle. CUBO 300-NC-FLAT is an Industry 4.0 tool and has the possibility to use it remotely.

Easy stops at 0°, graduated plate to identify different angles.
High blade tensioning 1700 kg / cm² to increase cutting accuracy and reduce cutting time.
Up to 99 different cutting lengths and number of cuts can be memorized, with the possibility to repeat them more than once.
CNC with programming of all operations; automatic calculation of the blade thickness.
Machine status shown on display, including blade speed, piece counter, and working anomalies. setting of the cutting lengths, minimal scrap-end 210 mm. Connection for loading table with 2 vertical rollers, unloading slide, connection for unloading table for cutting pieces.
Main switch with minimum tension coil, emergency button, thermic and magnetic motor protection.
Cutting capacity : round till 255 mm., square till 240 mm. and rectangular till 300×180 mm.
*The modem for Industry 4.0, teleservice and remote control is supplied as an optional





     

    Minimal lubrication system OPTIONAL

    It is possible to require , for all Imet machines, the minimal lubrication system , it avoids the dispersion of refrigerant liquid typical in the use of emulsifiable oil, the life of the blade is not in any way affected.

    Screw feeder

    In all our automatic NC Bandsaws the movement of the feeder is via a recirculating ballscrew and gear motor controlled by an inverter.

     

    Position Sensor BS 300

    In all our semiautomatic and automatic saws the detection of the start point of cutting occurs automatically through the position sensor.

     

    Microswitch end cut point BS 300

    In all semiautomatic and automatic saws the adjustment of the end cut point is via a lever that activates a microswitch of easy positioning

    Hydraulic Unit and electrical panel BS 300 AFI

    Practical positioning of the hydraulic unit for easy maintenance, electrical panel located under the control panel.

    Roller tables RTS

    Roller tables with free rolls, to use for loading side and unloading side, made of an electrowelded steel structure in forms of 2 meters each, with 7 galvanized steel rolls (of PVC for Velox models), the first element is with two adjustable height pedestals , the following ones with single pedestal. They include plates of protection among the rolls to avoid crushing. The structure is completely closed to avoid dispersions of coolant.

    Vertical rollers RTS

    To be combined with roller RTS, if the bundle cutting device is required, it is advisable to apply these vertical rollers on the roller table to hold over the entire length of the beams material (up to 6 pairs every 2 meters in length).

    Cubo 300-NC-Flat
    Area angular cut ° 90 +30
    Cutting capacity at 90°: round / square / rectangular mm. 255 / 230 / 300 x 180
    Blade dimensions mm. 2765 x 27 x 0.9
    Motor Blade Power KW 1.5
    Run feeder carriage (repeatable) mm. 515
    Feeder motor power KW 0.75
    Scrap end mm. 210
    Blade speed mt/min. 18 ÷ 110
    Motor Hydraulic Unit KW 0.75
    Tank Capacity of the hydraulic unit Lt 20
    Capacity coolant Tank Lt 100
    Dimensions ( B x L x H ) mm. 1800 x 1850 x 1880
    Height of the work-table mm. 870
    Weight Kg 680
    Minimum cuttable length mm. 4
    Type of functioning semiautomatic/automatic
    Suitable for cutting. Steel / cast iron / high-strength steels

    Liitu nordcity.ee uudiskirjaga, et olla kursis meie värskete uudiste ja parimate pakkumistega!