fbpx

CUBO 300 E-FLAT

IMET CUBO 300-E-FLAT Electronic automatic bandsaw

Electronic automatic bandsaw, hydraulically driven; mitre cutting from 0° to 45° left in automatic cycle and up to 60° left in semiautomatic cycle.
Cast iron saw frame with tubular section.
Adjustment of the blade tension from the front side of the sawframe, checked by an endstroke.
Blade guides with hard metal pads, additional bearing for blade alignment.
Feeder with 300 mm opening, maximum single stroke 515 mm, minimum stroke 4 mm, selection of the number of cuts (1-9999) and feeder strokes (1-29) by means of the keyboard.
Manual selection of the cutting length with digital reading and decimal accuracy.
Cutting capacity: round till 255 mm., square till 240 mm. and rectangular till 300×180 mm.





     

    Minimal lubrication system OPTIONAL

    It is possible to require , for all Imet machines, the minimal lubrication system , it avoids the dispersion of refrigerant liquid typical in the use of emulsifiable oil, the life of the blade is not in any way affected.

    BS 300 inverter OPTIONAL

    If required, the electronic inverter for variable blade speed allows the operator via keyboard to adjust the machine to be able to cut a wide range of materials and different sections. The change of speed is via inverter and it does not affect the power of the engine even at low speeds.

    Position Sensor BS 300

    In all our semiautomatic and automatic saws the detection of the start point of cutting occurs automatically through the position sensor.

     

    Microswitch end cut point BS 300

    In all semiautomatic and automatic saws the adjustment of the end cut point is via a lever that activates a microswitch of easy positioning

    Hydraulic Unit and electrical panel BS 300 AFI

    Practical positioning of the hydraulic unit for easy maintenance, electrical panel located under the control panel.

    Bundle Cutting BS 300 OPTIONAL

    On request the hydraulic device for bundle cutting is available. To view the cutting capacities download the brochure of the saw.

    Roller tables RTS

    Roller tables with free rolls, to use for loading side and unloading side, made of an electrowelded steel structure in forms of 2 meters each, with 7 galvanized steel rolls (of PVC for Velox models), the first element is with two adjustable height pedestals , the following ones with single pedestal. They include plates of protection among the rolls to avoid crushing. The structure is completely closed to avoid dispersions of coolant.

    Vertical rollers RTS

    To be combined with roller RTS, if the bundle cutting device is required, it is advisable to apply these vertical rollers on the roller table to hold over the entire length of the beams material (up to 6 pairs every 2 meters in length).

    Cubo 300-E-Flat
    Area angular cut ° 90 +30
    Cutting capacity at 90°: round / square / rectangular mm. 255 / 230 / 300 x 180
    Blade dimensions mm. 2765 x 27 x 0.9
    Motor Blade Power KW 1.5/1.8 or 1.5 ESC
    Run feeder carriage (repeatable) mm. 515
    Scrap end mm. 210
    Blade speed mt/min. 35/70 or 18 ÷ 110 ESC
    Motor Hydraulic Unit KW 0.75
    Tank Capacity of the hydraulic unit Lt 20
    Capacity coolant Tank Lt 100
    Dimensions ( B x L x H ) mm. 1800 x 1850 x 1880
    Height of the work-table mm. 870
    Weight Kg 630
    Minimum cuttable length mm. 4
    Type of functioning semiautomatic/automatic
    Suitable for cutting. Steel / cast iron / high-strength steels

    Liitu nordcity.ee uudiskirjaga, et olla kursis meie värskete uudiste ja parimate pakkumistega!