IMET CUBO 300-E-FLAT Electronic automatic bandsaw
Electronic automatic bandsaw, hydraulically driven; mitre cutting from 0° to 45° left in automatic cycle and up to 60° left in semiautomatic cycle.
Cast iron saw frame with tubular section.
Adjustment of the blade tension from the front side of the sawframe, checked by an endstroke.
Blade guides with hard metal pads, additional bearing for blade alignment.
Feeder with 300 mm opening, maximum single stroke 515 mm, minimum stroke 4 mm, selection of the number of cuts (1-9999) and feeder strokes (1-29) by means of the keyboard.
Manual selection of the cutting length with digital reading and decimal accuracy.
Cutting capacity: round till 255 mm., square till 240 mm. and rectangular till 300×180 mm.
| Minimal lubrication system OPTIONAL
It is possible to require , for all Imet machines, the minimal lubrication system , it avoids the dispersion of refrigerant liquid typical in the use of emulsifiable oil, the life of the blade is not in any way affected. |
 |
| BS 300 inverter OPTIONAL
If required, the electronic inverter for variable blade speed allows the operator via keyboard to adjust the machine to be able to cut a wide range of materials and different sections. The change of speed is via inverter and it does not affect the power of the engine even at low speeds. |
 |
| Position Sensor BS 300
In all our semiautomatic and automatic saws the detection of the start point of cutting occurs automatically through the position sensor.
|
 |
| Microswitch end cut point BS 300
In all semiautomatic and automatic saws the adjustment of the end cut point is via a lever that activates a microswitch of easy positioning |
 |
| Hydraulic Unit and electrical panel BS 300 AFI
Practical positioning of the hydraulic unit for easy maintenance, electrical panel located under the control panel. |
 |
| Bundle Cutting BS 300 OPTIONAL
On request the hydraulic device for bundle cutting is available. To view the cutting capacities download the brochure of the saw. |
 |
| Roller tables RTS
Roller tables with free rolls, to use for loading side and unloading side, made of an electrowelded steel structure in forms of 2 meters each, with 7 galvanized steel rolls (of PVC for Velox models), the first element is with two adjustable height pedestals , the following ones with single pedestal. They include plates of protection among the rolls to avoid crushing. The structure is completely closed to avoid dispersions of coolant. |
 |
| Vertical rollers RTS
To be combined with roller RTS, if the bundle cutting device is required, it is advisable to apply these vertical rollers on the roller table to hold over the entire length of the beams material (up to 6 pairs every 2 meters in length). |
 |
| Cubo 300-E-Flat | ||
| Area angular cut | ° | 90 +30 |
| Cutting capacity at 90°: round / square / rectangular | mm. | 255 / 230 / 300 x 180 |
| Blade dimensions | mm. | 2765 x 27 x 0.9 |
| Motor Blade Power | KW | 1.5/1.8 or 1.5 ESC |
| Run feeder carriage (repeatable) | mm. | 515 |
| Scrap end | mm. | 210 |
| Blade speed | mt/min. | 35/70 or 18 ÷ 110 ESC |
| Motor Hydraulic Unit | KW | 0.75 |
| Tank Capacity of the hydraulic unit | Lt | 20 |
| Capacity coolant Tank | Lt | 100 |
| Dimensions ( B x L x H ) | mm. | 1800 x 1850 x 1880 |
| Height of the work-table | mm. | 870 |
| Weight | Kg | 630 |
| Minimum cuttable length | mm. | 4 |
| Type of functioning | semiautomatic/automatic | |
| Suitable for cutting. | Steel / cast iron / high-strength steels | |
